Here are the steps to make a wind on leader. This is the process
I use… I’ve been using these for awhile now. They work well.Step 1. Get dacron. This is 130lb.
Image

Step 2. Cut off about 9 feet or so. Also bend a piece of malin
or afw wire in half. You need a 10 inch long doubled section. I
used 60lb.

This is the tool.
Image

Step 3. You’ll notice that the dacron is somewhat flat. Gently
press the tool through the dacron. You want do to this about 15
inches from

the end.
Image

Step 4. Put the tag end into the fold of wire.
Image

Step 5. Slowly pull the tag through.
Image

Image

Step 6. Should look like this. You now have the dacron threaded
through itself. You’ll have a long end and a tag end. During
this step, we

pulled the tag through the long end. (backbraided 1x)
Image

Step 7. Next we are going to go in through the tag and pull the
long end through. To do this put the tool through the tag end.
Where you

stick the tool through determines the loop size.
Image

Step 8. Put the long end in the tool.
Image

Step 9. Pull through.
Image

Image

Step 10. Put your finger in the first loop and pull gently. Both
sides will meetup. (backbraided 2x)
Image

Step 11. Next we are going to go in through the long side and
pull the tag through. Stick the tool through close to the
backbraid that is

developing. (backbraided 3x)
Image

Image

Image

Step 12. Go in through the tag and pull the long side through. (backbraided
4x)
Image

Step 13. Go in through the long side and pull the tag through. (backbraided
5x)
Image

Step 14. The basic loop is done! The rest is fairly easy.
Image

Step 15. Run the tool down through the dacron and out at the
loop.
Image

Step 16. Put the tag end into the tool and pull through.
Image

Step 18. This is what you’ll get.
Image

Step 19. Run the tool down through the dacron again and out
where the tag exits.
Image

Step 20. Put the middle of the tag end in the tool.
Image

Step 21. Pull through with the tag still doubled. The idea here
is to keep the tag folded in half inside of the dacron. So once
you get it

tight and before you pull it though, push the tool in the
opposite direction and out through the dacron. The dacron is
folded in half inside

itself. This makes it a little thicker and allmost equal to
300lb mono.
Image

Step 22. Your done with the loop. Steps 1-22 should take around
5-10 minutes once you figure it out.
Image

Step 23. Set the loop aside. Get your mono and some sandpaper.
This is 200lb mono.
Image

Step 24. Lightly sand the end of the mono. You want the sides to
be a little skinnier and the tip to be dome shaped.
Image

Step 25. The long end of your loop shoud look something like
this.
Image

Step 26. Start threading the end of the mono into the dacron.

Image

Image

Step 27. Keep threading. It’s an inchworming process.
Image

Image

Step 27. Thread it up untill it meets the doubled dacron from
the loop. (Step 21.)
Image

Step 28. You should have something like this.
Image

Step 29. Next we have to apply super glue gel to the connection.
We want to glue 10-12″ of mono. Scrunch back 10-12 inches of the
dacron,

keeping it between your thumb, index finger, and pinky.
Image

Step 30. Apply the super glue gel to the mono.
Image

Step 31. In one quick motion, let the scrunched up dacron go,
and run your fingers down the connection.
Image

Image

Step 32. Next, we are going to serve the connection so it can’t
unravel. Get about 2 feet of rigging or dental floss.
Image

Step 33. Double it and put it behind the connection.
Image

Step 34. Go around the mono and through the loop. Tighten!
Image

Step 35. Make a bunch of loop knots like this.
Image

Image

Step 36. If you keep your knot formation uniform, it will look
like this.
Image

Step 37. Keep going untill your 5 or 6 knots past the end of the
dacron. The last few knots will be on just mono. Once you feel
like you have

enough knots, pull the last on extra tight, snip it leaving 1/4″
of tag in the floss. Twist the floss strands together and heat
with a lighter.

This will make a blob that won’t pull back through all your loop
knots.
Image

Image

Step 38. Your done!
Image

From start to finish it takes me 10 minutes or so to make a
leader. They are very strong and hold up well. I have 100 feet
of 200 lb on my

9/0, 75 feet of 300lb on my 12/0, and 20 feet of 100lb on my
penn 9500. The 9500 casts extremely well and you can get away
with a shorter

‘bite’ leader.

Anyway, they are relatively easy to make, go through the guides
perfectly, and hold up well. You can make up a bunch and store
in leader

wallets or zip lock bags, so your always ready.

Credit to NCSHARKER for teaching me how to make these.